Following news that iniBuilds will be tackling the Airbus A310 after finishing up with the A300, the changelog for the group's debut airliner has been published showing what has been re-worked for version 1.10.

Alongside the changelog, which was published via a Forum post, a new 30-minute video has been shared by the team running through all of the additions and modifications in the new update.

In the forum post, six lines have been differentiated from the rest as 'major' changes. The first of these is a passenger variant of the Airbus, which launched as cargo-only back in August 2020.

Compatibility with macOS is also new with v1.10, in addition to two weather related changes: a new custom weather radar as well as compatibility with Active Sky XP to drive the new display.

"Major potential performance improvements" have also been implemented. These changes were detailed at the start of last month - see our article from the time here. Essentially, the main improvements span from only calling on systems when needed (instead of having them running all the time) and the removal of FPS degradation on longer routes.

A number of these performance enhancements were a result of systems re-works, with all of the following areas majorly changed: EFOB, ND drawing, A/THR, autoland, completely new thrust control logic and spool times.

Further to that, an impressive list of bugs and other issues have been fixed/updated - a full breakdown of those changes is available below:

• Fixed SASL Crash after selecting A/C STATUS in MDCU
• Fixed go around phase spool time/rate issue
• Fixed THR L spool time/rate issue
• Fixed Mach number in MCDU not matching commanded number
• Fixed v1 speed bug
• Fixed ANN LT dim not affecting all lights
• Fixed dome light illuminating without power
• Fixed issue with thrust dipping after engaging LVLCH
• Fixed issue where needle was clipping HYD pressure
• Fixed DME-only not functioning correctly
• Fixed thrust reverse N1 not being limited
• Fixed typos in EFB
• Fixed issue with airspeed target animation
• Fixed issue with ILS not displaying correctly
• Fixed issue with HDG not working correct is ROSE-mode
• Fixed issue with SID transition not being selectable
• Fixed issue with THR L coming on when pulling SPD knob
• Fixed issue with times being displayed in 24xx rather than 00xx in MCDU
• Fixed issue where wind correction showing as 5 instead of 0
• Fixed issue with TRP when selecting flex
• Fixed runway overlap issue in MCDU
• Fixed hidden holding button
• Fixed colour of localizer indicator at night
• Fixed random runways point added in flight plan
• Fixed issue with magnetic variation
• Fixed pointer showing in opposite direction in ARC mode
• Fixed issue with clock when crossing time zones
• Fixed issue with fire test with HP fuel open
• Fixed issue where runways would not show up on STAR page
• Fixed issue where the EFIS control panel was always powered
• Fixed issue where aircraft would not reach N1 for flex
• Fixed issue where shutdown and reset of aircraft would not clear the MCDU
• Fixed issue where approach and destination airport would disappear
• Fixed errors showing up on climb and cruise
• Fixed issue where aircraft was extremely slow to accelerate to commanded LVL CH Mach speed
• Fixed issue where T/D disappeared after direct to
• Fixed issue where CMD 1 fails to engage in SPD ALT* in LVL CH descent level off at a low altitude
• Updated yellow altitude intercept arc appearance
• Fixed issue when profile would go into Mach passing 10000ft
• Fixed issue where CRS that you set on the ILS was not reflected on the CRS page shown on ND
• Fixed issue where aircraft would descend without pulling the altitude knob
• Fixed issue where holding speed constraint is not respected in PROFILE mode
• Fixed nav issues with direct to and not following NAV
• Fixed EFB and MCDU weight/load differences
• Fixed issue where MCT N1 is higher than TO N1
• Fixed issue with APU bleed starting too quickly
• Fixed issue where turning off bleed after APU shutdown causes APU to turn on again
• Fixed terrain radar performance issues
• Fixed issue with THR RED and THR ACC settings from EFB not working correctly
• Fixed loss of altitude when in tight turns
• Fixed issue when using autobrakes MAX aircraft seems to apply MAX brakes without input
• Fixed issue with runways not loading with SID at LEBL
• Fixed issue with aircraft no descending on arrival at LMML
• Fixed issue where negative OAT value could not be entered into TO PERF in EFB
• Updated EFB items if ground vehicles connected
• Fixed issue where random white line would occur on ND
• Fixed issue with LAT/LONG on INS control panel not updating
• Fixed issue wither CI of 0 could not be entered into INIT A
• Fixed issue where MCDU would show negative EFOB values
• Fixed issue where EFB would freeze plane when requesting ATIS
• Fixed issue where western longitude was denoted with a negative sign in MCDU
• Fixed issue where parking brake would get stuck on
• Fixed issue when pressing the toe brakes, would play parking brake release noise.
• Fixed issue where all waypoints after T/D showed Mach .79

If you'd like a full rundown of all the changes in v1.10, check out iniBuilds' latest YouTube video where the A300 is put through its paces.

Alternatively, see the source post for this article on the iniBuilds Forum.